維修售后Sapphire Manual使用說明書球柵數顯表（顯示器、計數器）在本資料上方（或技術資料中）能下載帶圖的詳細說明書

維修及銷售的主要有日本富特巴(FUTEBA)、三豐（Mitutoyo）、英國新和(NEWALL)、萬濠(RATional)、怡信(Easson)、信和（Sino）、奧特嘉(oska)、朕衡(Zhen)、碩信(Soin)、必嘉(Bica)、艾莫特(AMOT)、意大利(Givi)等品牌.維修數顯表范圍：NEWALL球柵數顯表維修D(zhuǎn)P8、E70、B60、Mitutoyo三豐品牌（KACOUNTER、QM-DATA200、KLD-200、EC-100），Rational萬濠（WE6800-2、WE6800-3、WE6800E、DC3000），RSF-ELEKTRONIK，F(xiàn)AGOR（20I-M、30I-M），NEWALL新和（B60、E70、DP8），BICA-DRO，POWERN（PE2X、PE3X），HEIDENHAIN海德漢（ND780、ND522、ND523），NIKON尼康（DP-E1、SC2-E1、SC3-E1、QUADRA-CHEK200），CHFOIC（DRO-2M、DRO-3M、DRO-2L、DRO-2G、DRO-3E、JDS100B、DS401SM），SONY索尼（LH51、LH71、LH52、LH72），JENIX韓國東山，SUMTAK-FUTABA（FUTABA-PULSCALE、CMJ200），SINO諾信（SDS6-3V、SDS6-2V、SDS2MS），GSW-3A、GSW-3B、GSW-204、GSW-2B、GSW-2C，SOIN（SI2008-2B、SI2008-3B）維修售后Sapphire Manual使用說明書球柵數顯表（顯示器、計數器）

以上品牌和型號的數顯表都能維修：數顯表被雷擊壞、接錯電壓被燒壞、數顯表顯示軸跳數，顯示軸不顯示、顯示軸精度不準、顯示軸閃爍、數顯表按鍵不靈、數顯表無信號等等。

Digital Readout Systems                    Linear Encoders  

                     Troubleshooting Guide for Newall Digital Readout Systems  

                               For Display Models: Sapphire, DP7, DPG, Topaz, DP8, DPG2000, E70  

  This Troubleshooting Guide is intended for use in conjunction with the applicable user manuals. Please follow the troubleshooting steps below  

                                           and call our service department on (+44) (0)116 264 2730 with the results.   

              Nothing happens when the power switch is turned on (Axis windows are blank)  

1.     Ensure that the input voltage switch is set to the proper setting (115 / 230). This does not apply to DP7.  

2.     Check the fuse.  

3.     Test the input voltage to the display unit with a voltmeter.  

4.     Turn display off using the power switch.  

5.     Disconnect all reader head cables. A defective reader head could prevent the display from powering up.   

6.     Turn display on.  

                                                                  Inaccuracy in one axis  

1.     Get into “Setup mode” and check the following settings:  

    a)     Linear Compensation - Set to 0 on all axes.  

    b)     Scale Type / Input Type - Set to read the correct scale type (Spherosyn, Microsyn 5, Microsyn 10).  

    c)     Radius / Diameter - Diameter will display a 2:1 ratio. Radius will display a 1:1 ratio.  

2.     Put a dial indicator on the edge of the reader head. Move the axis. Compare the dial indicator reading to the display reading.  

       If there is a discrepancy that exceeds our accuracy specifications, proceed to the next step.  

3.     Take the reader head cable from the malfunctioning axis and plug it into the other axis of the display (You may need to get  

       into setup mode and ensure that this axis is set up to read the correct type of scale).  

4.     If the malfunction was corrected when the cable was moved to the other axis, the source of the fault is the display. The  

       display will need repaired.  

5.     If the malfunction followed the cable to the other axis, the source of the fault is the reader head and scale assembly. If this is  

       the case, proceed to the next step.  

6.     Check for any physical damage to the reader head and cable.  

7.     Check the reader head for proper alignment. It must be aligned within .002” on each side. Refer to the installation manual  

       for instructions on reader head alignment.  

8.     Check the scale to make sure there is no binding on the scale. If the scale brackets are slightly loosened, you should be able  

       to slide the scale back and forth through the brackets with minimal resistance.   

9.     If you have a Spherosyn scale, ensure that the scale is not bent. Remove the scale and roll it on a flat surface. If the scale is  

       bent at all, it will cause inaccuracies. Replace scale if bent.     

10.   If there is no binding on the scale, the reader head is aligned, and the scale is not bent, the malfunction must be coming from  

       the reader head. Replace the reader head.  

                                    Display shows “Signal Fail” or “No Signal” in one axis   

1.     Turn off display.  

2.     Take the reader head cable from the malfunctioning axis and plug it into the other axis of the display.   

3.     Turn display on.  

4.     If the scale works properly when connected to the other axis of the display, the source of the fault is the display. The display  

       will need repaired. Note: You may need to get into setup mode and adjust the scale type, radius / diameter, and linear  

       compensation (set to 0) parameters to get accurate readings. The main goal in this step is to identify the source of the signal  

       fail / no signal error.  

5.     If the malfunction followed the scale cable to the other axis of the display, the source of the fault is the reader head. Replace  

       the reader head.  

       Note: Signal Fail or No Signal errors can NOT be caused by incorrect parameter settings.